Hydraulics programme
-10 %
#FA16366
AK Regeltechnik
Additional control unit for Bosch SB7 hydraulics
Sale and shipment by: FAIE Handels GmbH
The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in delivery.Case-IHC: 844S, 846, 946, 1046, 1146, 1246, 743XL-856XL, 955XL-1055XL.Eicher:< /strong> King TigerFendt: 102, 103, 104, 105, 106, 108, 200S, 300, 304, 305, 306, 307, 308, 309, 310, 311, 312, 395GTA, 600, 610, 611, 612, 614, 615. Kramer: all models. Lindner: with Steyr transmission. MB-Trac: all models. Schlter: all models. Steyr: Anniversary series with control hydraulics, Plus series, Series 80.Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~< br>Locked floating position as fourth switching position after lowering
-13 %
#FA72297
Bondioli & Pavesi
Angle gear 1018 for circular saws with ratio 1:2.78, direction of rotation remains the same
Sale and shipment by: FAIE Handels GmbH
The angular gear 1018 is a compact and lightweight gear designed for use in circular saws. The gearbox has a gear ratio of 1:2.78, which means that the speed at the output of the gearbox is 2.78 times higher than the speed at the input. The direction of rotation of the output shaft is consistent with the direction of rotation of the input shaft (viewed from the visible end of the shaft). The angle gearbox is equipped with a high-strength aluminum housing, a PTO shaft profile 1 3/8 x 6 at the input and an output shaft with a diameter of 25 mm. The gearbox can accommodate torque peaks of up to 2 times the rated torque. of the nominal torque. ~We would like to point out that an overload protection device must be used in accordance with the performance data of the gearbox. Please note that before putting the gearbox into operation, fill and check the oil level. The maximum power transmission is 7kW at 540rpm and 11kW at 1000rpm. Compact and light High-quality workmanship High torque Long service life Universal applications< /li>
-8 %
#FA51049
Bondioli & Pavesi
Angle gear 1018 for circular saws with ratio 1:2.78, direction of rotation reversed
Sale and shipment by: FAIE Handels GmbH
The angular gear 1018 is a compact and lightweight gear designed for use in circular saws. The gearbox has a gear ratio of 1:2.78, which means that the speed at the output of the gearbox is 2.78 times higher than the speed at the input. The direction of rotation of the output shaft is opposite to the direction of rotation of the input shaft (viewed from the visible end of the shaft). The angle gearbox is equipped with a high-strength aluminum housing, a PTO shaft profile 1 3/8 x 6 at the input and an output shaft with a diameter of 25 mm. The gearbox can accommodate torque peaks of up to 2 times the rated torque. We would like to point out that an overload protection device must be used in accordance with the performance data of the gearbox. Attention, fill and check the oil level before putting the gearbox into operation. ~The maximum power transmission is 7kW at 540rpm and 11kW at 1000rpm.Compact and light< li>High-quality workmanshipHigh torqueLong service lifeUniversal applications
-31 %
#FA73758
asa
ASA oil cooler TT07 230/400V, asa rail system
Sale and shipment by: FAIE Handels GmbH
Aluminum oil air cooler in panel construction. Maximum flow 150 l/min, max. operating pressure 26 bar, protection class IP55.Delivered without connections and mounting base.Application: hay cranes, stationary small units
-15 %
#FA113947
Meta
Control valve 50/1 double-acting 12V electromagnetic actuation
Sale and shipment by: FAIE Handels GmbH
Electromagnetic actuation with spring return as standard. The middle position is designed with a pressureless circulation and ports A, B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard version of the valves in parallel connection. Version: DE50Flow max.: 50L/min Operating pressure: 250 barmax. Pressure: 300 barRelief pressure valve set: 100 bar, adjustable from 100-250 barScrew-in thread A, B: R3/8?Screw-in thread P, P2, T, T2: R1/2?H=Raise, 0=Middle position, S=Lower.The switching positions listed depend on the respective model of the control valve.
-13 %
#FA113955
Meta
Control valve 85/1 double-acting 12V electromagnetic actuation
Sale and shipment by: FAIE Handels GmbH
Electromagnetic actuation with spring return as standard. The middle position is designed with a pressureless circulation and ports A, B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard version of the valves in parallel connection. Version: DE85 Flow max.: 80L/min Operating pressure: 250 barmax. Pressure: 315 barRelief valve set: 100 bar, adjustable from 100-250 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T, T2: R3/4?H=Raise, 0=Middle position, S=Lower.The switching positions listed depend on the respective model of the control valve.
-29 %
#FA118035
GMS
Control valve GM08/1, double-acting with detent in lifting, for oil engine
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and the ports A &~ B are connected to the tank. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard design of the valves in parallel connection.Flow max.: 45 L/min.Operating pressure: 250 barmax. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R3/8?Screw-in thread T, T2: R1/2? HR=Raise locked, SW=Middle position - floating position, S=Lowering The switching positions listed depend on the respective model of the control valve.
-31 %
#FA118043
GMS
Control valve GM10/1 double-acting with detent in lifting
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and the ports A &~ B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard design of the valves in parallel connection.Flow max.: 90 L/min.Operating pressure: 250 barmax. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T, T2: R3/4? HR=Raise locked, 0=Middle position, S=Lowering.The switching positions listed depend on the respective model of the control valve.
-32 %
#FA118045
GMS
Control valve GM10/1 double-acting with locked floating position after lowering
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and ports A, B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard design of the valves in parallel connection.Flow max.: 90 L/min.Operating pressure: 250 barmax. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T1, T2: R3/4? H=Raise, 0=Middle position, S=Lowering, SW-R=Floating position lockedThe switching positions listed depend on the respective model of the control valve.
-38 %
#FA118132
GMS
Control valve GM10/1 double-acting, with detent in countersinks
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and the ports A &~ B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard design of the valves in parallel connection.Flow max.: 90 L/min.Operating pressure: 250 barmax. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T, T2: R3/4? H=Raise, 0=Middle position, SR=Lowering locked.The switching positions listed depend on the respective model of the control valve.
-39 %
#FA118128
GMS
Control valve GM10/1 single-acting with detent in countersunk
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and ports A, B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard design of the valves in parallel connection.Flow max.: 90 L/min.Operating pressure: 250 barmax. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T, T2: R3/4? H=Raise, 0=Middle position, SR=Lowering lockedThe switching positions listed depend on the respective model of the control valve.
-19 %
#FA118042
GMS
Control valve GM10/1 single-acting with spring return
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and the ports A &~ B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.Standard design of the valves in parallel connection.Flow max.: 90 L/min.Operating pressure: 250 barmax. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T, T2: R3/4? H=Raise, 0=Middle position, S=Lowering.The switching positions listed depend on the respective model of the control valve.
-33 %
#FA118135
GMS
Control valve GM10/2 DW-SR DW with spring return
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and the ports A &~ B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.1. Double-acting control slide DW-SR: H=Raise, 0=Middle position, SR=Lowering locked2. Double-acting control slide DW: H=lifting, 0=middle position, S=loweringStandard version of the valves in parallel connection.Flow max.: 90 L/min.Operating pressure: 250 bar max. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T, T2: R3/4?
-30 %
#FA118140
GMS
Control valve GM10/3 DW EW EW with spring return
Sale and shipment by: FAIE Handels GmbH
Mechanical actuation with spring return as standard. The middle position is designed with a pressureless circulation and the ports A &~ B are blocked. Pressure relief valve at connection P (pump). Negative overlap of the slides.1. Double-acting control slide DW: H=lifting, 0=middle position, S=lowering2. Single-acting control slide EW: H=Raise, 0=Middle position, S=Lower3. Single-acting control spool EW: H=lifting, 0=middle position, S=loweringStandard version of the valves in parallel connection.Flow max.: 90 L/min.Operating pressure: 250 bar max. Pressure: 315 barRelief valve set: 100 bar, adjustable from 20-315 barScrew-in thread A, B, P, P2: R1/2?Screw-in thread T, T2: R3/4?The switching positions listed depend on the respective model of the control valve. 1. Double-acting control slide DW: H=lifting, 0=middle position, S=lowering2. Single-acting control slide EW: H=Raise, 0=Middle position, S=Lower3. Single-acting control slide EW: H=lifting, 0=middle position, S=lowering
#26325
Hydraulic cylinder piston � K = 25 mm, piston rod � S = 16 mm
Installation length (EL) (mm):
286
|
Stroke (mm):
200
Sale and shipment by: FAIE Handels GmbH
Pressure force 883 kg, tensile force 521 kg at 180 bar, connection G 1/4, nominal pressure 250bar
Variants from €79.00*
-14 %
#FA132311
Hydraulic pump BG2 19.2ccm/rev with transmission gear i=1:3.8
Sale and shipment by: FAIE Handels GmbH
For the hydraulic drive of firewood splitters, cable winches, forestry cranes, etc.Consisting of:1 piece transmission gear with PTO shaft stub 1:3.81 piece hydraulic pump BG2 19.2cm /rev., clockwise rotation1 piece pump driver1 pieces angle flange for suction pipes R1/2 inch female thread1 pieces angle flange for pressure pipe R3/8 inch female threadDelivered in individual parts!Calculation example:Wood splitter with hydraulic cylinder inner diameter 100 mm, stroke 1000 mm, speed on the PTO shaft 350 rpm.For use comes a gearbox with a ratio of 1:3.8. This results in a pump speed of 1330 rpm (350 x 3.8 = 1330 rpm).The hydraulic pump delivers 36L/min at a PTO speed of 350 rpm.
-14 %
#FA63171
Hydraulic pump BG2 26.2ccm/rev with transmission gear i=1:3.8
Sale and shipment by: FAIE Handels GmbH
For the hydraulic drive of firewood splitters, cable winches, forestry cranes, etc.Consisting of:1 piece transmission gear with PTO shaft stub 1:3.81 piece hydraulic pump BG2 26.2cm /rev., clockwise rotation1 piece pump driver1 pieces angle flange for suction pipes R3/4 inch female thread1 pieces angle flange for pressure pipe R1/2 inch female thread Delivered in individual parts!Calculation example:Wood splitter with hydraulic cylinder inner diameter 100 mm, stroke 1000 mm, speed on the PTO shaft 350 rpm.For use comes a gearbox with a ratio of 1:3.8. This results in a pump speed of 1330 rpm (350 x 3.8 = 1330 rpm).The hydraulic pump delivers 36L/min at a PTO speed of 350 rpm.
-13 %
#FA132313
Hydraulic pump BG3 32,3 ccm/rev with transmission gear i=1:3.8
Sale and shipment by: FAIE Handels GmbH
For the hydraulic drive of firewood splitters, cable winches, forestry cranes, etc.Consisting of:1 piece transmission gear with PTO shaft stub 1:3.81 piece hydraulic pump BG3 32,3 ccm /rev., clockwise rotation1 piece pump driver1 pieces angle flange for suction pipes R1 inch female thread1 pieces angle flange for pressure pipe R3/4 inch female threadDelivered in individual parts!Calculation example:Wood splitter with hydraulic cylinder inner diameter 100 mm, stroke 1000 mm, speed on the PTO shaft 350 rpm.For use comes a gearbox with a ratio of 1:3.8. This results in a pump speed of 1330 rpm (350 x 3.8 = 1330 rpm).The hydraulic pump delivers 36L/min at a PTO speed of 350 rpm.
-13 %
#FA63172
Hydraulic pump BG3 43,4 ccm/rev with transmission gear i=1:3.8
Sale and shipment by: FAIE Handels GmbH
For the hydraulic drive of firewood splitters, cable winches, forestry cranes, etc.Consisting of:1 piece transmission gear with PTO shaft stub 1:3.81 piece hydraulic pump BG3 43.4 ccm /rev., clockwise rotation1 piece pump driver1 pieces angle flange for suction pipes R1 inch female thread1 pieces angle flange for pressure pipe R3/4 inch female threadDelivered in individual parts!Calculation example:Wood splitter with hydraulic cylinder inner diameter 100 mm, stroke 1000 mm, speed on the PTO shaft 350 rpm.For use comes a gearbox with a ratio of 1:3.8. This results in a pump speed of 1330 rpm (350 x 3.8 = 1330 rpm).The hydraulic pump delivers 36L/min at a PTO speed of 350 rpm.
-10 %
#FA120651
SAUGUT
Hydraulic top link Cat.2 with catch hook and ball eye, stroke 200mm
Sale and shipment by: FAIE Handels GmbH
The hydraulic top link Cat.2 SAUGUT from FAIE with catch hook and ball eye is a high-quality product that is suitable for a variety of applications. The top link has a stroke of 200 mm, a piston diameter (inner cylinder tube) of 60 mm and a piston rod diameter of 35 mm. The hydraulic top link can be used on tractors up to approx. 90 HP, has a pressure force of 5100 kg and a pulling force of 3620 kg.The top link is complete with connecting hoses(length 1m), Control chain equipped with catch hook, top link ball and stroke indicator. It also has a hydraulically unlockable check valve (locking block). ~The hydraulic top link from the SAUGUT series from FAIE is a robust and reliable product that is designed for a long service life. It is easy to assemble and operate and offers excellent performance.Piston K = 60mm, piston rod S 35mm up to approx. 90HP, pressure force approx. 5100kg, tensile force approx. 3620kg.The specified lengths always refer to the centre of the pin to the centre of the pin!
-12 %
#FA120652
SAUGUT
Hydraulic top link Cat.2 with catch hook and ball eye, stroke 250mm
Sale and shipment by: FAIE Handels GmbH
The hydraulic top link Cat.2 SAUGUT from FAIE with catch hook and ball eye is a high-quality product that is suitable for a variety of applications. The top link has a stroke of 250 mm, a piston diameter (inner cylinder tube) of 70 mm and a piston rod diameter of 35 mm. The hydraulic top link can be used on tractors up to approx. 120 HP, has a pressure force of 6927 kg and a pulling force of 5195 kg.The top link is complete with connecting hoses(length 1m), Control chain equipped with catch hook, top link ball and stroke indicator. It also has a hydraulically unlockable check valve (locking block). ~The hydraulic top link from the SAUGUT series from FAIE is a robust and reliable product that is designed for a long service life. It is easy to assemble and operate and offers excellent performance.Piston K = 70mm, piston rod S 35mm up to approx. 120HP, pressure force approx. 6927kg, tensile force approx. 5195kg.The specified lengths always refer to the centre of the pin to the centre of the pin!
-12 %
#FA123679
SAUGUT
Hydraulic top link Cat.2 with catch hook, ball eye and top link bracket, stroke 200mm
Sale and shipment by: FAIE Handels GmbH
The hydraulic top link Cat.2 SAUGUT from FAIE with catch hook and ball eye is a high-quality product that is suitable for a variety of applications. The top link has a stroke of 200 mm, a piston diameter (inner cylinder tube) of 60 mm and a piston rod diameter of 35 mm. The hydraulic top link can be used on tractors up to approx. 90 HP, has a pressure force of 5100 kg and a pulling force of 3620 kg.The top link is complete with connecting hoses(length 1m), Control chain for catch hook, top link ball and stroke indicator as well as a top link bracket. It also has a hydraulically unlockable check valve (locking block). ~The hydraulic top link from the SAUGUT series from FAIE is a robust and reliable product that is designed for a long service life. It is easy to assemble and operate and offers excellent performance.Piston K = 60mm, piston rod S 35mm up to approx. 90HP, pressure force approx. 5100kg, tensile force approx. 3620kg.The specified lengths always refer to the centre of the pin to the centre of the pin!
-14 %
#FA123680
SAUGUT
Hydraulic top link Cat.2 with catch hook, ball eye and top link bracket, stroke 250mm
Sale and shipment by: FAIE Handels GmbH
The hydraulic top link Cat.2 SAUGUT from FAIE with catch hook and ball eye is a high-quality product that is suitable for a variety of applications. The top link has a stroke of 250 mm, a piston diameter (inner cylinder tube) of 70 mm and a piston rod diameter of 35 mm. The hydraulic top link can be used on tractors up to approx. 120 HP, has a pressure force of 6927 kg and a pulling force of 5195 kg.The top link is complete with connecting hoses(length 1m), Control chain for catch hook, top link ball and stroke indicator as well as a top link bracket. It also has a hydraulically unlockable check valve (locking block). ~The hydraulic top link from the SAUGUT series from FAIE is a robust and reliable product that is designed for a long service life. It is easy to assemble and operate and offers excellent performance.Piston K = 70mm, piston rod S 35mm up to approx. 120HP, pressure force approx. 6927kg, tensile force approx. 5195kg.The specified lengths always refer to the centre of the pin to the centre of the pin!
-16 %
#FA67752
DNP
Multi-clutch 4-way set
Sale and shipment by: FAIE Handels GmbH
Automated workflows in manufacturing, testing, controlling and regulating require the highest precision. This is where our multi-coupling 4-way set comes into play: It allows you to effortlessly connect several oil hydraulic lines at the same time. The fixed arrangement of the coupling elements eliminates confusion and the duration of the coupling process is shortened enormously. There are neither fluid losses nor air inclusions during the coupling and uncoupling phases, even when ~ Presence of pressure. Incorrect connections are virtually impossible.The 4-way multi-coupling set is used here:Hydraulic equipment for agricultural machinesHydraulic equipment for forestry machinesHydraulic equipment for conveyor machinesHydraulic equipment for commercial vehiclesComponents on test benches for hydraulic systemsCooling or heating when molding plastic and metal< li>Hydraulic systems in industrial applicationsHydraulic systems for special transport vehicles ~Scope of delivery / technical data:Complete with fixed and loose parts Assembly 2, DN10Pressure max. 350 barFlow 45 L/minConnection R1/2"
€10 voucher.
If you sign up for our newsletter.
You will receive €10 for free with your next purchase.