Control units & directional control valves

With check valve and emergency drain screw. Can be used as an electromagnetic stopcock, as an opener or closer for simple hydraulic controls. Duty cycle 100%.

With check valve and emergency drain screw. Can be used as an electromagnetic stopcock, as an opener or closer for simple hydraulic controls. Duty cycle 100%.

The valve is designed as a 3/2-way changeover valve. In the neutral position, connection P is connected to connection A~ when energized, connection P is connected to connection B. The control magnet can be supplied for different operating voltages. Small internal leaks are permitted because the valve is designed as a slide valve. A magnetic plug (FAIE No. 28483) can optionally be supplied. The valve can be used in all common hydraulic systems. Technical data: max. operating pressure: 250 bar max. return pressure: 10 bar< br> Nominal flow: 40 l/min Tightening torque: 78 Nm Coverage: positive Connections: G3/8 Weight: 2.46 kg Dimensions: 162.5x46x65 mm Operating fluid: Hydraulic oil according to DIN 51524 Viscosity: 10-200 Operating temperature: -20 to +80C

Can be used as an electromagnetic 3-way tap. Basic position de-energized - continuity from P to B. Switched position - continuity from P to A. 100% duty cycle.

6/2-way changeover valves are suitable for tractors and tractors, attachments, telehandlers, excavators, backhoe loaders, wheel loaders and many other machines. Switching valves are used to switch a double function through electrical control. The application takes place between a hydraulic control block and two different hydraulic functions or hydraulic consumers. Basic position without current - continuity P1/P2 to C/D. Switched position - continuity P1/P2 to A/B. Duty cycle 100%. With leak oil connection R1/4",directional valve 8/3, double flanged, galvanized.

6/2-way changeover valves are suitable for tractors and tractors, attachments, telehandlers, excavators, backhoe loaders, wheel loaders and many other machines. Switching valves are used to switch a double function through electrical control. The application takes place between a hydraulic control block and two different hydraulic functions or hydraulic consumers. Basic position without current - continuity P1/P2 to C/D. Switched position - continuity P1/P2 to A/B. Duty cycle 100%. With leak oil connection R1/4",directional valve 8/3, double flanged, galvanized.The specified operating pressure refers to operation without a connected leak oil line!

e.g. for front loaders to operate the front loader bucket and to open and close the silo bale gripper via 1 control valve. 6/2-way changeover valves are suitable for tractors and tractors, attachments, telehandlers, excavators, backhoe loaders, wheel loaders and many other machines. Switching valves are used to switch a double function through electrical control. The application takes place between a hydraulic control block and two different hydraulic functions or hydraulic consumers. Flow 50 L/min, voltage 12 V, connections R1/2", operating pressure 250 bar. With leak oil line.The specified operating pressure refers to operation without a connected leak oil line!

e.g. for front loaders to operate the front loader bucket and to open and close the silo bale gripper via 1 control valve. 6/2-way changeover valves are suitable for tractors and tractors, attachments, telehandlers, excavators, backhoe loaders, wheel loaders and many other machines. Switching valves are used to switch a double function through electrical control. The application takes place between a hydraulic control block and two different hydraulic functions or hydraulic consumers. Flow 50 L/min, voltage 24 V, connections R1/2".The specified operating pressure refers to operation without a connected leak oil line!

6/2-way changeover valves are suitable for tractors and tractors, attachments, telehandlers, excavators, backhoe loaders, wheel loaders and many other machines. Switching valves are used to switch a double function through electrical control. The application takes place between a hydraulic control block and two different hydraulic functions or hydraulic consumers. Basic position without current - continuity from P1/P2 to C/D. Switched position - continuity from P1/P2 to A/B. 100% duty cycle. With leak oil connection R 1/4"The specified operating pressure refers to operation without a connected leak oil line!

e.g. for front loaders to operate the front loader bucket and to open and close the silo bale gripper via 1 control valve. 6/2-way changeover valves are suitable for tractors and tractors, attachments, telehandlers, excavators, backhoe loaders, wheel loaders and many other machines. Switching valves are used to switch a double function through electrical control. The application takes place between a hydraulic control block and two different hydraulic functions or hydraulic consumers. Flow 50 L/min, voltage 12 V, connections R3/8".The specified operating pressure refers to operation without a connected leak oil line!

The 6/2-way valve is suitable for expanding a double-acting hydraulic function. e.g. for front loaders to operate the front loader bucket and to open and close the silo bale gripper via 1 control valve. Without current, the oil flows from ports P1 and P2 to ports C and D. If the magnet is energized, the oil flow is diverted from ports P1 and P2 to the additional consumers A and B. This valve can be used as a universal valve and can can be expanded directly with the same valve. Small internal leaks are permitted because the valve is designed as a slide valve.

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in delivery.

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in delivery.Case-IHC: 844S, 846, 946, 1046, 1146, 1246, 743XL-856XL, 955XL-1055XL.Eicher:< /strong> King TigerFendt: 102, 103, 104, 105, 106, 108, 200S, 300, 304, 305, 306, 307, 308, 309, 310, 311, 312, 395GTA, 600, 610, 611, 612, 614, 615. Kramer: all models. Lindner: with Steyr transmission. MB-Trac: all models. Schlter: all models. Steyr: Anniversary series with control hydraulics, Plus series, Series 80.Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~< br>Locked floating position as fourth switching position after lowering

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in the scope of delivery.Deutz: All types built up to 1984, DX85, DX90, DX110, DX120, DX145 until the switch to large glass doors.Connection thread:< /strong> M18x1.5mm internal thread ~Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~Locked floating position as fourth switching position after lowering

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation.Deutz: 07C series, DX3.10-DX4.70, Agro Prima 4.31-6.17, Agro Xtra 3.57-6.07, Star Cab Series, DX90-145 with large glass door.Switchable from single-acting to double-acting ~Hydraulic limit switch in raising ~Locked floating position as fourth switching position after lowering

The version is a mobile control block with 2 additional control devices, a switching valve from the original hydraulics to the additional control device and an operating lever for the three-point hydraulics via the additional control device. Installation is carried out using a mounting plate on the hydraulic riser pipe. The two additional control devices can be used double-acting. The outer control spool can be switched from single-acting to double-acting.The functions of the additional control valve are:Lever No. 1, Switching valve from original hydraulics to additional control unit Lever up: normal tractor hydraulic Lever down: work control valveLever No. 2, actuation of the three-point hydraulics without control hydraulics when switching to the additional control unit with lever No. 1, position downLever No. 3, double-acting control deviceLever No. 4, double-acting control device can be switched to single-acting via the changeover tap on the side of the end plate. If the changeover tap is screwed onto the seat, the control slide can be used double-acting. If the changeover cock is turned out to the stop, the function of the control slide is switched to single-acting.The operating lever of the tractor hydraulics/power lift must be in the outer hydraulics position so that the function of the additional control unit is guaranteed. The scope of delivery includes:The screws for attaching to the hydraulic block are included. ~There is also a hose package with 4 hydraulic hoses and matching hollow screws, ~ 4 pieces of clutch sleeves with dust protection and a holder for the clutch sleeves for attaching to the differential housing included. ~

This control valve is a /4-way valve that is operated manually to control single-acting and double-acting cylinders as well as hydraulic motors. The control valve from AK- Regeltechnik was developed specifically for Fiatagri tractors with Kontak hydraulics. Due to the high liter output, up to 4 control valves can be flanged directly. Since the hole pattern is completely identical to Kontak/Parker, this valve can also be installed with original Kontak/Parker control valves. The valve is a four-position device. It can be converted from double-acting to single-acting and vice versa. The control valve is a slide-sealed valve that exhibits absolutely neutral fine control behavior and allows extremely low fit leakage even at higher pressures. The device has a locked safety limit switch in the LIFTING position. If you switch further via the LOWER position, you will reach a locked floating position. This can be returned to the NEUTRAL position manually at any time.

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The valve can be mounted on the left or right using a freely positionable sealing plate. The sealing plate is included in delivery.Bosch: 0 521 609 001, 0 521 609 005, 0 521 609 009, 0 521 609 013, 0 521 609 015, 0 521 609 019, 0 521 609 021, 0 521 609 022, 0 521 609 053, 0 521 609 054, 0 521 609 062, 0 521 609 063, 0 521 609 064.0 521 609 074, 0 521 609 098. Case-IHC: 743XL-844XL, 585XL (BJ 87/88), 1055XL, 1255XL, 856XL, 956XL-1056XL, 1256XL(A)-1455XL(A), CS48-CS150, 3220, 4210, 4220, 4230, 4240. Deutz: Agro Star 4.61-6.81, Agro Tron 4.70-4.95, 6.00, 6.05, 6.15, 6.20, 6.30. Fastrac: 135, 155, 185, 525, 1115. JCB Fastrac: 130, 135, 150, 155, 185, 1115, 1135, 2115.Lindner: Geo Trac. Massey-Ferguson: 3000 series. Steyr: 900, 9000 series. Valmet: 6000, 6200 , 6300, 6400, 8000, 8100, 8200, 8300, 8400. Zetor: 3320-3341, 4320-4340, 5320-5341, 6320-6341, 7320-7540, 8520-18345 . ~Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~Locked floating position as fourth switching position after lowering

This connection plate is fitted as a replacement for the gearbox cover. The plate has 4 hydraulic connections on the top for P=pump, R=return, W=pressure transfer and Z=additional lift cylinder. This plate makes it possible to connect an externally mounted control unit. If no control valve with pressure transfer line is used, the W connection is closed. In order to guarantee the function of the tractor hydraulics with this installation, a shut-off-valve is fitted in the pressure line between connection P and the control valve. This must be closed when the three-point hydraulic system is used. This prevents pressure from escaping via the tank line of the additionally installed control valve.If a mobile control valve with pressure transfer line is used, connection W is connected to the pressure transfer line connection on the mobile control valve. This allows the tractor hydraulics and the mobile control valve to be used simultaneously. No shut-off-valve is required!Can be used in hydraulic systems of Ford tractor systems 3000, 4000, 5000.Max. Operating pressure: 250 barNominal flow rate 70 l/minTightening torque 78 Nm Connections M18x1.5 Dimensions (LxWxH): 160 x 130 x 20 mm

Electric black/white joystick switches with 2 or 4 functions. max. 5A, cable length 3 m

Electric black/white joystick switches with 2 or 4 functions. max. 5A, cable length 3 m

This main control unit is used in the tractor to control and regulate the hitch. With the control valve, attachments attached to the hoist can be raised and lowered continuously. The position control keeps a position preselected on the control lever (height of the attachment) constant. The traction control allows optimal use of the tractor's performance. Depending on the type of application, the control valve can also be used for mixed control of position and tension control. The control system constantly corrects disturbances automatically, making driving the tractor much easier.The control unit is equipped with a lowering throttle, with which the lowering speed of the hoist can be adjusted.There is an additional connection for the return on the front of the switch cap .Not an original replacement part!

This main control unit is used in the tractor to control and regulate the hitch. With the control valve, attachments attached to the hoist can be raised and lowered continuously. The position control keeps a position (height of the attachment) preselected on the control lever constant. The traction control allows optimal use of the tractor's performance. Depending on the type of application, the control valve can also be used for mixed control of position and tension control. The control system constantly corrects disturbances automatically, making tractor driving much easier. The valve is very extensively equipped with additional connections for R and P, as well as continuous adjustment of P.The control unit is equipped with a lowering throttle, with which the lowering speed of the hoist can be adjusted.A sealing plug is included in the scope of delivery must be used in the valve if there are only 2 hydraulic connections on the hydraulic flange surface. The non-existent connection must be closed with the plug on the control valve. The sealing plug is held in its position by being flanged to the power lift.There is an additional connection for the return line at the front of the switch cap.Not an original replacement part!

​Hydraulic control valve in monobloc design with electromagnetic 12 volt operation and manual emergency operation via hand lever. Standard radio valve for FAIE crane cable winches. The solenoid valve is double-acting and has a connection for pressure transfer,The connections to the working cylinders are locked in the zero position - no floating position in the O position!Technical data:12 V 3 AFlow rate max. 50 l/min.Operating pressure: max. 175 barConnections: 1/2 inch female thread inlet/outlet and consumer, 1/2 inch male thread for pressure transferControl valve with additional manual emergency operation.