Landtechnik

​Maximum service life, perfect soil cultivation and a universal fit: our carbide-tipped coulter point from the “eXtreme” series is the ultimate solution for farmers who want to minimise downtime and maximise the efficiency of their soil cultivation. Farmers need to be able to rely on their machinery and wear parts, particularly during the busy season. This premium wear part has been specially developed for extreme conditions and combines maximum robustness with uncompromising flexibility.Your benefits at a glanceLonger service life: Thanks to the precisely applied carbide plates, the coulter tip withstands even the hardest, stony soils and severe abrasion. This saves time and money through significantly less frequent replacement intervals.Universal hole pattern (39–81 mm): No more searching for the right specialised part. Thanks to the flexible hole spacing of 39 to 81 mm, this tip fits a wide range of common cultivator models.Optimal geometry for a 300 mm radius: The curvature is precisely matched to cultivator tines with a 300 mm radius. This ensures an optimal penetration angle, perfect soil contact and reduced traction requirements for your tractor.Versatile: Whether for shallow stubble cultivation, deep loosening or incorporating slurry – this coulter tip delivers a clean finish in every application.Consistent working quality: Thanks to the carbide, the coulter tip retains its shape almost perfectly throughout its entire service life. Upgrade your cultivator to premium quality and drastically reduce your we ar and tear costs per hectare! 

Brake fluid: DOT4 brake fluid

​Piston diameter: ø 25.4 mmBrake fluid: DOT4 brake fluid

In agricultural technology, scraper floors are often driven with a hydraulic drive via an oil motor in conjunction with a scraper floor gear. These drives can be found in loading wagons, manure spreaders and also in chopping wagons. For this purpose, gearboxes with a high reduction ratio and a high transferable torque are used. The gearboxes are supplied with different diameters for the drive shaft. A hydraulic motor with a shaft diameter of 25 mm and an SAE-A flange is used on the input side. The design of the hydraulic motor depends on the required speed of the scraper floor shaft and the available liter output of the hydraulic pump. In general, torque peaks of up to 2 times the nominal torque do not cause any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.Delivery without oil motor!

In agricultural technology, scraper floors are often driven with a hydraulic drive via an oil motor in conjunction with a scraper floor gear. These drives can be found in loading wagons, manure spreaders and also in chopping wagons. For this purpose, gearboxes with a high reduction ratio and a high transferable torque are used. The gearboxes are supplied with different diameters for the drive shaft. A hydraulic motor with a shaft diameter of 25 mm and an SAE-A flange is used on the input side. The design of the hydraulic motor depends on the required speed of the scraper floor shaft and the available liter output of the hydraulic pump.In general, torque peaks of up to 2 times the nominal torque do not cause any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.Delivery without oil motor!

Headliner for Steyr cab RS1 and RS2

​Steyr headliner suitable for high-roof models, with cutout for the passenger seatHeight: 5 cm

​Steyr headliner suitable for low roof version, with cutout for passenger seatHeight: 3 cm

with a cutout for the roof hatch

For the hydraulic drive of firewood splitters, cable winches, forestry cranes, etc.Consisting of:1 piece transmission gear with PTO shaft stub 1:3.81 piece hydraulic pump BG2 19.2cm /rev., clockwise rotation1 piece pump driver1 pieces angle flange for suction pipes R1/2 inch female thread1 pieces angle flange for pressure pipe R3/8 inch female threadDelivered in individual parts!Calculation example:Wood splitter with hydraulic cylinder inner diameter 100 mm, stroke 1000 mm, speed on the PTO shaft 350 rpm.For use comes a gearbox with a ratio of 1:3.8. This results in a pump speed of 1330 rpm (350 x 3.8 = 1330 rpm).The hydraulic pump delivers 36L/min at a PTO speed of 350 rpm.

31 blades 59015, 6 guide bars, B590.59032

Seal / oil seal 130x160x15 with dust lip for sealing the rear of the crankshaft

​Rotary harrow tines compatible with Breviglieri and Regent KSE, in OEM quality! The flanged tine is secured to the rotor with two M16x1.5x55 mm bolts. The tines are fitted in either a left-hand or right-hand version, depending on the direction of rotation of the rotor.

​"Steyr" sticker for the right rear fenderDimensions: 235 x 58 mm

​Are you looking for a completely reliable solution for professional drinking water supply? Our drinking water hose, featuring a tear-resistant polyester fabric lining embedded in an inner and outer layer of high-quality thermoplastic polyurethane (PU), combines extreme durability with uncompromising hygiene. Fitted with robust Storz couplings, this hose is ready for immediate use in demanding, continuous operation.Areas of application:    Drinking water supply    Drinking water transfer hose    Emergency supply hoseAdvantages:    Extremely pressure-resistant: With a maximum operating pressure of 17 bar, this hose effortlessly withstands even severe pressure surges and intense stresses.    Top-quality material: Manufactured from modern polyurethane (PU). This makes the hose not only extremely light and flexible, but also highly abrasion-resistant, UV-resistant and durable.    Easy to clean and disinfect thanks to the very smooth inner surface    100% safe for drinking water: The inner material is completely tasteless, odourless and certified for the transport of clean drinking water (complies with all current KTW and DVGW guidelines).    Quick connection: The factory-fitted Storz couplings guarantee a connection in a matter of seconds – drip-free and absolutely secure – in the blink of an eye.