Hydraulic pumps and accessories
Angled connection piece 90�
3-hole mounting flange with O-ring and screws.
Angled connection piece 90�
4-hole mounting flange with O-ring and screws.
Double pump 22.5 + 14 cc, suitable for Deutz and Fendt
Vivoil double pump suitable for Deutz and Fendt, and the following Bosch part numbers: 0 510 765 315, 0 510 765 332, 0 510 765 335, 0 510 765 336. Robust and high-performance gear pump for reliable use in agricultural machinery and hydraulic systems. Ideal as a replacement for a faulty original pump. High-quality workmanship and excellent operational reliability. The front section of the pump, with a displacement of 22.5 ccm, is designed to supply the tractor’s hydraulic system. The rear section of the pump supplies hydraulic oil to the steering system.
Elastic coupling
Used to connect hydraulic pumps with a 1:8 tapered shaft and electric motors. The conical bore depends on the size BG1, BG2 or BG3 of the hydraulic pump. Material: AluminiumThe largest diameter of the cone is on the side of the hydraulic pump: Size 1 9.7 mm Size 2 17.2 mm Size 3 22.2 mm
Electric motor for flange-mounting hydraulic pumps
Three-phase motor 4-pole, speed 1500rpm, up to 2.0kW 230/400V, from 3.0kW 400/690V, design B3/B5 with flange and feet. Protection class IP55.
Front bearing for hydraulic pump with cylindrical shaft
Particularly suitable for drives where there is a larger radial load, e.g. drive via V-belt pulley.Don't forget to order matching drive pinions for the front bearing for the hydraulic pump! You can find these on page 465 at the bottom right.
Hand pump for tank construction, double-acting, double stroke
With 4-way valve and check valve in A+B, including seal and fastening screws.
Hand pump for tank construction, double-acting, double stroke
With 4-way valve and drain cock, including seal and fastening screws.
Hand pumps for tank construction, single-acting, double stroke
Includes gasket and mounting screws.
HI-LO hydraulic pump BG2 11 + 19 cc, 70 - 210 bar
A new product has been added to the Vivoil product range: the HI-LO double pump. HI stands for high pressure, LO for low pressure. The HI-LO pump is essentially a double pump in which the primary pump operates at high pressure with a low flow rate, while the secondary pump delivers a high flow rate at low pressure. Below a certain pressure (decoupling pressure), the flow rate corresponds to the sum of the flow rates of the front and rear stages. Above the decoupling pressure, the rear stage operates in a closed circuit and does not deliver any flow rate. Under these conditions, only the front stage operates, whose flow rate is determined exclusively by its displacement volume, as it reaches the maximum pressure required for the application.One of the most common applications for these pumps is in presses or wood splitters. The HI-LO VIVOIL pump is essentially a double pump, with the first pump generating the high pressure and the second pump delivering the low-pressure volume flow in addition to the volume flow of the high-pressure pump for fast movements. Below a certain pressure, the cut-off pressure set by the pressure relief valve, the volume flow delivered by the double pump corresponds to the sum of the volume flows of the two pump stages. The HI-LO pump also offers many individual customisation options. Ask us about the numerous customisation options available.
Hydraulic hand pump with tank, double-acting with 4-3 directional control valve
Hydraulic hand pumps are used in hydraulic systems where only one hydraulic movement is required. These are mostly simple systems where high pressure with low flow rate is required, such as bending tools, lifting devices, tipping devices for car trailers and smaller agricultural trailers, etc. Hand pumps are a simple and inexpensive solution for operating double-acting hydraulic cylinders. The extension and retraction of the hydraulic cylinder is controlled by the integrated 4-3 directional control valve.The hand lever is included.Connection thread: 3/8" BSP internal thread
Hydraulic hand pump with tank, single-acting
Hydraulic hand pumps are used in hydraulic systems where only one hydraulic movement is required. These are mostly simple systems where high pressure with low delivery capacity is required, such as bending tools, lifting devices, tipping devices for car trailers and smaller agricultural trailers, etc. Hand pumps are a simple and inexpensive solution for operating single-acting hydraulic cylinders. The hydraulic cylinder is retracted by opening the drain cock and using the weight of the load.The hand lever is included.Connection thread: 3/8" BSP internal thread
Hydraulic hand pump without tank, single acting, double stroke
For universal use in agriculture and industry. The simple and inexpensive solution for operating hydraulic cylinders.
Hydraulic hand pumps without tank, single acting, double stroke
For universal use in agriculture and industry. The simple and inexpensive solution for operating hydraulic cylinders.
€10 voucher.
If you sign up for our newsletter.
You will receive €10 for free with your next purchase.
