Radio remote control

​Pull cylinder with built-in release spring, installation length centre-to-centre 405 mm, total length 430 mm, stroke: 85 mm, cylinder inner diameter 35 mm, cylinder outer diameter 45 mm, piston rod 25 mm, forks with 11 mm holes, connection: R 3/8"UF AG.

​Hydraulic control valve in monobloc design with electromagnetic 12 volt operation and manual emergency operation via hand lever. Standard radio valve for FAIE crane cable winches. The solenoid valve is double-acting and has a connection for pressure transfer,The connections to the working cylinders are locked in the zero position - no floating position in the O position!Technical data:12 V 3 AFlow rate max. 50 l/min.Operating pressure: max. 175 barConnections: 1/2 inch female thread inlet/outlet and consumer, 1/2 inch male thread for pressure transferControl valve with additional manual emergency operation.

​Electromagnetic actuation with spring return to the centre position = floating position. The centre position is designed with an unpressurised circulation and connections A, B are both open into the return flow. Pressure relief valve on connection P (pump). Negative overlap of the gate valves.Standard version of the valves in parallel connection.Version: DE50Max. flow rate: 50 litres/minOperating pressure: 250 barMax. pressure: 300 barPressure relief valve set: 100 bar, adjustable from 100-250 barScrew-in thread A, B: R3/8″Screw-in thread P, P2, T, T2: R1/2″H=lifting, 0=centre position = SW = floating position, S=lowering. 

Radio control with hydraulic control valve!2-channel radio control set for hydraulically driven winches, oil motors or hydraulic cylinders with 12 volt monoblock valve, the radio is pre-wired with a 7-pin vehicle plug , the solenoid valve is double-acting and has a connection for pressure continuation, technical data: 12 volts 3 amps, flow rate max. 50 L/min. Connections: 1/2?IG inlet/output and consumer<~cbht/>~1/2?AG to continue printing

​For easy retrofitting of a radio control system – NO complicated cable connections! All components are permanently wired and easy to install! 2-channel radio device with wired receiver and transmitter with on/off switch and two functions. The input on the receiver is hard-wired with a 7-pin automotive connector and the outputs with a 3-pin DIN plug each.Frequency: ISM 868 / 915 MHzOutputs max. 5 A,Protection class: IP 67.

​PPlug-ready radio set for 12 and 24 volts!For easy retrofitting of a radio control - NO complicated cable connection!All components are pre-wired and easy to install!2-channel radio set with wired receiver and transmitter with on/off switch and two functions. The 2-pole input on the receiver can be connected to 12 V or 24 V and the outputs each with a 3-pin DIN plug. Frequency: ISM 868 / 915 MHz  Outputs max. 5 A, Protection class: IP 68.

Suitable for single and double cable winches with electromechanical or electrohydraulic actuation. Also for simple industrial applications, such as: B door or barrier opening systems, switching fans or floodlight systems on and off as well as for smaller mobile applications such as winches for off-road vehicles. Designed for extreme environments with the highest challenges in terms of vibration, dust, moisture and shock resistance, robust and easy to use.Technical data: 12/24 volt DC, protection class IP67, ~ 25mA power consumption at 12V, 869.8 MHz GMSK frequency, 50ms switching time, dimensions: 120x90x50 mm, weight 350g,

For single rope winch ~new with 4 buttons: on and off switch and two switching functions. ~Shockproof, fiberglass reinforced housing with easy-to-use buttons (even with gloves). can be pressed over a million times.Radio range: max. 300 meters with a clear view without obstacles!Technical data: ~incl. 2x AA batteries (3 volts), protection class IP67, 15mA power consumption when sparking, ~Dimensions: 100x60x25 mm, ~Weight 130g

For double cable winch with 6 buttons: on/off switch and five switching functions, ~shockproof, fiberglass reinforced housing with easy-to-use buttons (even with gloves) that can be pressed over a million times.Radio range: max. 300 meters with a clear view without obstacles!Technical data: incl. 2x AA batteries (3 volts), protection class IP67, 15mA power consumption when radioing, ~ Dimensions: 100x60x25 mm, ~Weight 130g

Set for conversion of a mechanically operated forestry winch on a hydraulic operation with Radio control. ~You only need a rasterized one , double-acting control valve, or a single-acting valve with free return and a 12 volt supply. ~The hydraulic cylinder operates the operating lever via a wire cable. This means that the standard cable pull operation still works. ~The cylinder pulls the lever via radio control - the cable winch pulls. As soon as you no longer operate the transmitter, a ~spring pushes the cylinder back - the cable winch stops.  ~As soon as the radio transmitter is no longer operated - the winch stops - safety circuit!ATTENTION: Please note the increased risk of tipping over with radio control - always keep eye contact with the wood and vehicle!Technical data: ~Maximum flow 20 l/min - TIP: most older tractors do not have more l/min at idle speed! ~Adjustable pressure limiter. ~Radio range: max. 150 meters outdoors without obstacles !The radio control set for mechanically powered winches is a great way to increase safety and flexibility when using winches. ~The Set contains a 12 V valve, a hose, a cylinder and a radio with wiring. ~The valve and the cylinder are mounted on the winch , and the radio is placed in a convenient location.The radio can then be used to operate the winch without you having to be near the winch. ~This can occur in dangerous situations or difficult environments. The radio control set is also very easy to install and operate. ~It is a great way to increase safety and flexibility when using winches. ~Here are some of the Advantages of the radio control set for mechanically driven winches: ~Increased safety: You don't have to be near the winch to operate it. This can be very helpful in dangerous or difficult environments. ~ Increased flexibility: You can operate the winch from anywhere, which can help you use the winch more efficiently.Easy installation and operation: The set is very easy to install and operate.  ~Suitable for maximum flow rate of 20 l/min. ~If you are looking for a safe and flexible way to operate your winch, The radio control set for mechanically driven winches is the perfect solution for you.

Set for converting a mechanically operated forestry winch to a hydraulic operation with radio control.You only need a latched, double-acting control valve, or a single-acting valve with free return and a 12 volt supply. ~The Hydraulic cylinder operates the operating lever via a wire cable. This means that the standard cable pull operation still works.The cylinder pulls the lever via radio control - the cable winch pulls. As soon as you no longer operate the transmitter, a ~spring pushes the cylinder back - the cable winch stops.  ~As soon as the radio transmitter is no longer operated - the winch stops - safety circuit!ATTENTION: Please note the increased risk of tipping over when using radio control - always keep eye contact with the wood and vehicle!Technical data : ~Maximum flow 50 l/min.Adjustable pressure limiterRadio range: max. 100 m outdoors without obstacles