Agricultural machinery parts

Compact multi-grab shovel with EURO holder

The compact multi-grab shovel for universal use is suitable for loading loose or bulky goods such as manure or shrub cuttings. The screwed side panels prevent load losses. The compact multi-grab bucket is available for tractors, farm loaders and wheel loaders with a Euro mount. Thanks to the high opening width, the edge of the bucket can be moved towards a wall when the gripper is open. Total height 645 mm, blade plate 6 mm thick, including side plates, plug BG3, double scraper edge 500HB

Complete rear crank bearing housing, 281.0090

Rear crank bearing housing for driving the bedknife on Busatis and ESM double knife mowers.

Cooking tines without a share

Tine material 25x8.

Crowd loose

Working width 105 mm, suitable for Regent chipper.

Double beam blade 2-hole

98x74x3 mm, hole spacing 51 mm

Hammer mallet suitable for

Agricom, Agritec, Berti, Breviglieri, MEAAT, Mthing, Oehler, Vigolo, Vogel and Noot, AP-00891

Hammer mallet suitable for

Agricom, Becchio &~ Mandrile, Desvoys, Kuhn, Kverneland, Maletti, MEAAT, Nobili, Omarv, Perugini, Rinieri, Vogel and Noot, Zappator

Injector double flat jet nozzle AI3070 TeeJet

AI3070 with two wide-angle flat jets, therefore very suitable for lower spray heights for better use of the droplet energy during deposition.30 jet forward in the direction of travel optimizes penetration in the upper leaf and ear area on the front sides, 70 jet towards the rear covers rear target areas.Drop sizes like short AIXR TeeJet and therefore the perfect compromise between loss reduction and degree of coverage. Large, round, free cross-sections for liquid and air increase operational safety and wear.Plastic designInjector can be removed if necessary.Automatic alignment with Quick TeeJet cap and seal Order No. 72989 Pressure range 1.5 - 6 bar, optimal 2 - 5 bar.Typical applications: Ear treatmentsother fungicides and insecticides in grain, leafy crops and special crops, potato cultivationHerbicides, especially for grasses and rough fields .

Interchangeable tip S1W

Knife for WELGER RP200

long cutting edge

Knife holder F22S, FN22S, N22R, N22RS

Loading wagon knife for P�TTINGER Siloprofi, Loading Professional, Harvesting Professional

Thickness 5mm

M-back Austro-Rap.1400 DIN80

Metal wheel 2.0 'Basic', 2 pieces (1 pair), used demonstration wheels

Metal wheel 2.0 Basic suitable for many motor mowers up to a weight of 150kg. The metal wheel has a diameter of 420mm (corresponds to rubber tires 4.00 x 8), a width of 190mm and the centering hole has a diameter of 60.5mm. The fastening hub is made with 2 hole circles 4x100mm. A hole circle with the hole diameter for M12 collar screws and a hole circle for fastening with cone screws with a hole diameter of 15mm. The cone rings are welded into the hub.The delivery consists of a pair of metal wheels!The powder-coated metal wheel has a hardened tread on the outer contour and is therefore very resistant to abrasion. Thanks to the nested and welded construction, the wheel is very stable. How it works!Due to the offset outer contour or the overlap of the wheel lugs, a closed radius is created. This creates a closed radius You get perfect concentricity on hard surfaces such as a road without vibrations or shock loads on the driver and drive axles.The design of the wheels ensures a gentle crop flow of the forage from the knife bar right behind the wheels. Due to the geometry of the wheels, there is no wrapping the axles with food. The metal wheels 2.0 are designed in such a way that they clean themselves while driving. When mowing on soft ground, the wheel cleats engage in the ground. By immersing the driving lugs into the ground, the inner radius and the connecting struts are now the new running surface of the wheels. The controlled immersion of the driving lugs creates a uniform linear drive in which there is hardly any pulling to one side - regardless of whether it is on a slope or with uneven meadow vegetation.Another positive effect is the ground footprint that the driving lugs leave by immersing it in the ground. This footprint promotes water absorption on steep slopes. The metal wheel 2.0 Basic is suitable for motor mowers weighing up to 150kg. For heavier mowers, a wider version is recommended. In this case, please contact us or fill out the inquiry form available for download with the required technical data and send it to us. You will then receive a tailor-made offer for the right pair of metal wheels for your motor mower.Scope of delivery: 2 pieces of metal wheels

Moll plate edges for Moll plates U13, UN350

Mounting triangle Cat.3

For coupling front and rear implements, material fine-grain steel QSTE380 (St52-3). Made from frame profiles 60x60x5mm.

Mounting triangle/device triangle in a set

For coupling front and rear implements, reinforced version.

Mower blade suitable for M�rtl High-Florett (fully hydraulic drive) with cutter head NY535/1

19 blades N336 + 5 guide blades F336R = 24 Kl.

Original mower blade set for double blade mower 6'

Set with a cutting width of 1.9 m, comprising Upper blade DME1606 A – 25 blades = 5460.055.63 = 262.5990 and lower blade DME 1606B – 26 blades = 5470.055.61 = 265.5980.Suitable for AEBI TT33 with front mower, Busati BM1102 rear mower, Rasant Nußmüller KombiTrak, Reform Metrac 2002, 2004, 3000Original No. 221.601.920 and many more.Upper blade:Total length including blade head: 1940mmLength of blade back: 1850mmBlade head 5840.052.01, 345.0690 Blade head projection beyond blade back: 57 mm Blade head length: 235 mm Blade head pin diameter: 16 mm Blade head orientation when viewed in the direction of travel: leftTotal number of blades: 25, including 5 mushroom blades Position of the mushroom blades relative to the blade head 3rd, 8th, 13th, 18th and 23rd bladesBlade spacing (centre-to-centre): 76 mmOriginal ESM upper blade: 262.5990Lower blade:Total length including blade head: 2000 mmLength of blade back: 1965 mmBlade head 5840.053.01, 345.0700 Blade head projection beyond the blade back: 28 mm Blade head length: 360 mm Blade head pin diameter: 16 mm Blade head viewed in the direction of travel: leftTotal number of blades: 26, of which 4 are mushroom blades and 1 is an end blade Position of the mushroom blades relative to the cutter head 6th, 11th, 16th and 21st bladesBlade spacing (centre to centre): 76 mmOriginal ESM lower blade: 265.5980

Overload clutch with locking body, 1 3/8x6

clockwise, for loading wagons, manure spreaders, rotary haymakers, rakes,...

Professional wood grabber/forestry grabber/loading tongs/brushwood grabber including safety valve

Forestry grab with open tongs for precise work, offers more precision and efficiency, especially when loading. The reinforced tips make it ideal as a brush gripper and for wood chip production, as almost no soil or dirt is lifted. Including mounted locking block on the cylinder: serves as a safety valve in the event of a hose break and relieves the load on the control valve!

Rotary hay tine turbo hay

share screw

with square approach

Skid instead of Kuhn K6805620

Skid suitable for Kuhn disc mower type FC and GMD. The skid is painted, tempered and hardened.