Agricultural machinery
All Products
The plastic oil level indicators or level indicators are suitable for checking the oil level in tanks and hydraulic systems.The polyamide material used has high mechanical strength and resistance to oil, lubricants, solvents, gasoline and most chemicals.The maximum operating temperature is 100C.
Oil pan gasket suitable for 4-cylinder MWM engine
O-ring for the oil filler neck when venting through the oil filler cap Part number: 103 Dimensions: O-ring 35x5
When machinery and equipment are parked, the hydraulic lines are often under residual pressure, or pressure may have built up due to heating caused by, for example, sunlight. Connecting to the tractor’s hydraulic system is then difficult or completely impossible. In such cases, the hydraulic connector is struck against a solid object to open the valve and release the pressure. This causes the hydraulic oil to spray in all directions and also leads to hydraulic oil seeping into the ground. Over time, the coupling nipple at the front of the connector is also damaged.The oil pressure relief pliers allow the excess pressure in the hydraulic line at the connector to be released in a controlled, safe and environmentally friendly manner. No more splattered work areas or oily clothing!
Oil pressure gauge 60mm suitable for Steyr T180
Complete with return filter, filler neck with pressure relief valve 0.35 bar, oil level indicator with temperature display and suction connection with shut-off valve. A 1/4? internal thread is provided for the ventilation in order to screw in a ventilation filter, e.g. Faie No. 12833, or to be able to attach a ventilation line. The inside of the tank is blank (not painted).Filter connection: G1" IT
The oil tank is supplied complete with a lid and lid seal. A drain with a 1/2" BSP internal thread is fitted on the side to allow the tank to be completely emptied.The steel tank is primed with anti-rust paint.
Spherical graphite cast iron sprocket / chain wheel, suitable for Bergmann spreaders.
10-28Volt, with chrome ringInstallation 52mm
10-28Volt, with chrome ringInstallation for 60mm
Advantages:Accurate operating hours recording, speed display from 100 rpmManipulation-proofEasy installation, robust, reliable constructionNo additional costs due to battery operation Power supply necessary, long battery life Cost-effective purchase Function: A sensor disk with an integrated magnet is mounted on the PTO connecting shaft on the implement. At a short distance from this there is an inductive sensor that records the rotational movements and forwards them to the counting device. The counting process/time measurement only begins when the idle speed of the PTO shaft has exceeded 100 rpm. The counting device is equipped with a digital hour and minute display. The switch between operating hours display and speed display occurs automatically. As soon as the revolutions of 100 rpm are reached, the speed is displayed. When the drive shaft subsequently comes to a standstill, the display switches to the operating hours.Easy installation:The encoder disc is pushed over the standardized PTO shaft connecting piece and secured with a locking screw. An inductive sensor records the speed and passes it on to the operating hours counter. The cable length from the sensor to the display is 1.5m.
Set with a cutting width of 1.9 m, comprising Upper blade DME1606 A – 25 blades = 5460.055.63 = 262.5990 and lower blade DME 1606B – 26 blades = 5470.055.61 = 265.5980.Suitable for AEBI TT33 with front mower, Busati BM1102 rear mower, Rasant Nußmüller KombiTrak, Reform Metrac 2002, 2004, 3000Original No. 221.601.920 and many more.Upper blade:Total length including blade head: 1940mmLength of blade back: 1850mmBlade head 5840.052.01, 345.0690 Blade head projection beyond blade back: 57 mm Blade head length: 235 mm Blade head pin diameter: 16 mm Blade head orientation when viewed in the direction of travel: leftTotal number of blades: 25, including 5 mushroom blades Position of the mushroom blades relative to the blade head 3rd, 8th, 13th, 18th and 23rd bladesBlade spacing (centre-to-centre): 76 mmOriginal ESM upper blade: 262.5990Lower blade:Total length including blade head: 2000 mmLength of blade back: 1965 mmBlade head 5840.053.01, 345.0700 Blade head projection beyond the blade back: 28 mm Blade head length: 360 mm Blade head pin diameter: 16 mm Blade head viewed in the direction of travel: leftTotal number of blades: 26, of which 4 are mushroom blades and 1 is an end blade Position of the mushroom blades relative to the cutter head 6th, 11th, 16th and 21st bladesBlade spacing (centre to centre): 76 mmOriginal ESM lower blade: 265.5980
Diameter: 125mmOuter plate PTO shaft clutch Steyr ~
Unser Produktleiter
Werner Meixner
€10 voucher.
If you sign up for our newsletter.
You will receive €10 for free with your next purchase.
