Quick-change frame

for hydraulic device operation with 1 cylinder to the quick-change frame. The mounting kit is delivered pre-cut in a piece of sheet metal (962x150 mm). For assembly, only the remaining webs are cut through so that the individual parts can be welded. Sheet thickness 15 mm. Delivery corresponds to the parts colored red.

Simple and quick coupling and uncoupling of implements on Category 2 and 3 front loaders. The upper mounting bolts enable individual tilt angle adjustment by repositioning. The quick-change frame also has a mechanical central locking system. Locating bolt on the front loader side 30 mm, receiving shaft on the device side 40 mm, mounting width of the front loader swing arm inside minimum 855 mm and outside max. 1120 mm, locking bolt 20 mm, total width 1159 mm, weight 59 kg. With a load center of 800 mm, the load capacity is approx. 3000 kg.The quick-change frame in conjunction with hydraulic actuation enables a cost-effective conversion to a fully hydraulically controlled modern loader. This opens up a wide range of new areas of application for your old front loader. With the EURO attachment you increase the impact power and expand the possible uses of your old front loader in many areas.

Simple and quick coupling and uncoupling of implements on Category 2 front loaders. The upper mounting bolts enable individual tilt angle adjustment by repositioning. The quick-change frame also has a mechanical central locking system. Locating bolt on the front loader side 30 mm, receiving shaft on the device side 40 mm, mounting width of the front loader swing arm inside minimum 860 mm and outside max. 1120 mm, locking bolt 20 mm, total width 1159 mm, weight 60 kg. With a load center of 800 mm, the load capacity is approx. 3000 kg.The quick-change frame in conjunction with hydraulic actuation enables a cost-effective conversion to a fully hydraulically controlled modern loader. This opens up a wide range of new areas of application for your old front loader. With the EURO attachment you increase the impact power and expand the possible uses of your old front loader in many areas.

Simple and quick coupling and uncoupling of implements on category 2 and 3 front loaders. The upper mounting bolts enable individual tilt angle adjustment by repositioning. Locating bolt on the front loader side 30 mm, receiving shaft on the device side 40 mm, mounting width of the front loader swing arm inside minimum 860 mm and outside max. 1120 mm, locking bolt 20 mm, total width 1159 mm, weight 60 kg. With a load center of 800 mm, the load capacity is approx. 3000 kg. Hydraulic locking with a double-acting cylinder. Includes 1.5 m hose with connection M18x1.5/12L union nut.

Simple and quick coupling and uncoupling of implements on Category 2 front loaders. The upper mounting bolts enable individual tilt angle adjustment by repositioning. The quick-change frame also has a mechanical central locking system. Locating bolt on the front loader side 30 mm, receiving shaft on the device side 40 mm, mounting width of the front loader swing arm inside minimum 860 mm and outside max. 1120 mm, locking bolt 20 mm, total width 1159 mm, weight 60 kg. With a load center of 800 mm, the load capacity is approx. 3000 kg. The side locking can be easily converted from the right side to the left side by loosening 2 screws.The quick-change frame in conjunction with a hydraulic actuation enables a cost-effective conversion to a fully hydraulic one controlled modern loader. This opens up a wide range of new areas of application for your old front loader. With the EURO attachment you increase the impact power and expand the possible uses of your old front loader in many areas.

​Quick and easy coupling and uncoupling for implements on category 2 (85 cm) and 3 (102 cm) front loaders. The upper mounting bolts can be repositioned to allow individual tilt angle adjustment. The quick-change frame also has a mechanical central locking system. Mounting pins on the front loader side 30 mm, mounting shaft on the implement side 40 mm, mounting width of the front loader arm minimum 855 mm inside and maximum 1120 mm outside, locking pin Ø 20 mm, total width 1165 mm, weight 57 kg. With a load centre of gravity of 800 mm, the load capacity is approx. 3000 kg.The quick-change frame is suitable as a replacement for OEM front loader change frames.

​Quick and easy coupling and uncoupling for implements on category 2 (85 cm) and 3 (102 cm) front loaders. The upper mounting bolts allow individual tilt angle adjustment by repositioning. The quick-change frame also has a hydraulic locking mechanism. The hydraulic hose lines with a length of 1.5 m are included in the scope of delivery. The lines have a connection with an M18x1.5 mm union nut - 12L connection. Mounting pin on the front loader side 30 mm, mounting shaft on the implement side 40 mm, mounting width of the front loader arm minimum 855 mm inside and maximum 1120 mm outside, locking pin Ø 20 mm, total width 1165 mm, weight 53 kg. With a load centre of gravity of 800 mm, the load capacity is approx. 3000 kg.The quick-change frame is suitable as a replacement for OEM front loader change frames.

For converting the mechanical locking to a hydraulic locking of the implements with a double-acting cylinder. Including 1.5 m hose, connection M18x1.5/12L union nut.In conjunction with guide no. 103099 (see accessories) you can attach this conversion kit to any quick-change frame. The installation length L(min) is 714mm. With the stroke of 150mm, the maximum length L(max) is 864mm. The locking bolt has a diameter of 20mm.We would like to point out that the hydraulic control circuit for the locking cylinder has a flow rate of 10-15L/min. and the maximum pressure should be limited to 160bar.